#81
|
||||
|
||||
Finished up the inner fenders
Working on completing the front sides of the fenders Cutting up and using another trailer fender Used the planishing hammer to round off the cut edge to match the rest of the fender Going to use some metal mesh to make some compartments in the corners of the bed which will be covered by the bed sides. http://www.BenModified.com |
#82
|
||||
|
||||
Wow nice work on that fender, that is some oldskool metal work
|
#83
|
||||
|
||||
Quote:
Thanks! Here is todays progress. Engine compartment venting to the Bed Pocket in corner of the bed for venting and hauling greasy items or just things that I don't want sliding around, chain etc. This will be hidden by the Bed Sides http://www.BenModified.com |
#84
|
||||
|
||||
The passenger side is done!
Pocket behind the right rear wheel Welded on some Dzus fasteners for a removable cover over the charcoal canister behind the left rear wheel. Took the measurements for an Aluminum Treadplate bed floor. Going to the big city soon to pick it up. They have a huge shear so I can get the size I want and nice smooth lines. http://www.BenModified.com http://www.facebook.com/BenModified |
#85
|
||||
|
||||
Seriously impressive.
It's a great thread to read through and the craftmanship is amazing. Can't wait to see the endproduct on the road
__________________
Golf 1 1977 in the making
|
#86
|
||||
|
||||
Quote:
Thanks! Got it running today, trying to post the video now but will likely take hours to load. 1080p |
#88
|
||||
|
||||
Sprayed the frame rails under the bed floor with some aerosol bed liner. Also drilled and tapped all the bed floor mounting points and bought some nylon washers to place between the bed floor and frame rails to allow air floor and prevent moisture accumulation. 1/4" Aluminum Bed Floor Started playing around with an idea for the headlights. I made up a reversible locking spring loaded headlight mount to secure some polished bullet headlights. When rotated back, they resemble the dagmar bumperettes. And started making up the under the cab lower rails. Benmodified.com |
#89
|
||||
|
||||
|
#90
|
|||
|
|||
Long testdrive
Nice work !!
__________________
|
#91
|
||||
|
||||
Was that a cop car during the testdrive?
__________________
Welcome to the internet: Where men are men, women are men, and little girls are FBI agents. |
#92
|
||||
|
||||
Quote:
Thanks! I will post more after I get the through the break in period! |
#93
|
||||
|
||||
Quote:
Yes, but I am legal even without the glass as long as I am wearing eye protection. Seat belts are not required as the VW did not have them from the factory. Last edited by Ben Modified : 05-01-2016 at 11:30. |
#94
|
||||
|
||||
Started on a cage for the cab today. When finished, it will have 3 sets of 3 point seat belts!
|
#95
|
||||
|
||||
|
#96
|
||||
|
||||
Installed the Safari Windshields today.
Fabricated a couple of outboard mounts and welded to the roll cage. Much stronger than stock. http://www.BenModified.com |
#97
|
|||
|
|||
Looks very nice !
__________________
|
#98
|
||||
|
||||
Wow nice progress, the welding looks very good. The sound is nice are you mounting any other pipes to boost the noise
|
#99
|
||||
|
||||
Quote:
No, the noise is already sufficiently boosted! The camera just doesn't do a good job of recording it. Last edited by Ben Modified : 11-01-2016 at 11:17. |
#100
|
||||
|
||||
I finally got around to re-covering the seat frame for the truck. Got tired of riding around on a piece of cardboard! I went ahead and installed seat heaters while I was at it.
http://www.BenModified.com |