I love this built

__________________
Welcome to the internet:
Where men are men, women are men, and little girls are FBI agents.

Thanks mate

What should have been finished has been put onto the back burner due to demanding wife [8(]
Sad times .....life used to be so good [:[]













The old plants sitting idle two years now

???

__________________
Welcome to the internet:
Where men are men, women are men, and little girls are FBI agents.

Why are all the posts deleted?

__________________
Daily Golf V GTI DSG

Golf 2 1984, 1.3 -> tdi -> TDI ->VR6

Mmm, sad.

__________________
Volkswagen Golf MK1 1.1
Volkswagen Golf MK1 1.6 GTI
Volkswagen Golf MK1 2.1 G60

Shortshifter MK1 02A

Been Busy and fell out with the woman who went mad on my Pc ...a lot of topics
killed ...Sorry guys ...been busy fixing them and even done a bit more on my dub

Airbox time [:s]

Foam is falling to bits and I hate things not right, so had to come apart




Think most look something like this now






Best to split to remove flaps




Old foam removed and found some new foam from mk4 golf door panel speaker blanks




All cleaned and good to go, just going to get more foam tomorrow

Just getting the last bits I need to finish her then hope to get stuck in again next month

Went to creationsmotorsport_uk
For the Mk2 to Brembo brake lines ...nice and easy and came the next day



Then after a bit of searching I managed to find a set of flat center caps for my Rays, with the Black longer nut covers will be sweet
Wee note.... These would not have fitted the car before as the standard bearing hub cap stuck out to far, but running polo gti ones now.
Same colour as rims and Alloy.






Pic on Rim




Here like Whats the craic you lot [:[]

Been well busy

Cover removed





Nice and tidy




Can't beat a nice bit of blue office carpet




Wiring tidied up unwanted plugs and wiring removed

























Look tape next







One loom done and in the car next up engine loom
Got a fair bit through it tonight

Both looms now sorta sorted just to run them down legs and find a place for ecu

Wee drop of wax round boots
seen mk2's rust round these holes






Had a new servo sitting in my loft

New and old










Seat Ibiza Cupra R master cylinder and Ford focus one on car








My new center caps from Japan

These wheels don't come with center caps when you buy them
German Performance wheel of choice
Wee links
Click on

https://www.google.co.uk/search?q=P...iw=1440&bih=775

https://www.google.co.uk/search?q=P...k+Te37&tbm=isch













The power cable to hide battery in the car




Dash in to see what room I have under it for ECU tis looking good




Wiring and more wiring [:s]

Working through wiring today, wanted to utilize the holes in the shell

Nice wee blanks in the chassis, removed these and found me some Vag Grommets to fit in nice




Front wiring and plugs



















Ran the rest of the wiring through scuttle to hide it and take part of it to the ecu in to car via the heated washers wiring grommet




Wiring ran down both legs and brought up through leg to the washer motor and a loop earth I added

Sorting battery cable and finishing wiring earths etc






To wiper motor and the other to Emerald inside car



Battery cable Grommet in leg and lighting wiring run




Center tail is for sensors and starter etc ..right hand tail is for level sensor in coolant bottle




loop earth

Battery cable sorted ..bit of G sheet cut to fit the inset and keep feed cable safe and reseal floor








Bit of hard wax sealer



Where it comes out




sorted







Next up was sort out the wiring on rear of Dash
New feed added etc



Dash fitted




My Wideband and anything else you want, it does it all



Cover time




Quiet day do going to make a few pipes up
Everything you will need, you can get brake pipe pliers but not needed
wee alloy bar with a cutout I put in it does everything I need.
Thing I don't like is copper/nickel copper pipe as its not factory looking
also copper goes off and looks crap ...so mine will be copper/black [8D]
more pic's soon










Work out what length you need and leave a bit on so once you shape it, then trim if need be before fitting nut
Wee pipe cutter




Make sure end is flat ..wee file






Pop in









Job done



Shape pipes by hand and finish them once clipped into place



So far so good







Clipped and wee heat shield I made added







Next up was drivers front pipe which comes back across













Last to finish front was passanger side pipe

The Brake shield, seen these on Subarus so made on for the Dub out of wifes special K box





Cardboard wasn't going to fly so .....









Bit of an after thought

Pipes all finished, just need to bleed

Looks better than copper










Rear pipes Sorted







Bleeding sorted ..pedal good




Back on her wheels and side skirts fitted










Back under cover [!]

Engine and gearbox ready to go together then in [:*:][:*:][:-B]







Gearbox with VR6-FD,quaife and Seat Actuator ...I like clutch cables ..throttles cables ....its old like me so it's right




Well Got power steering sorted and good to go







Skyhook in place